Effect of nanoparticles orientation on morphology of polymeric nanocomposite foams: preparation of foamed nanocomposite fibers by supercritical carbon dioxide

ABSTRACT

Polymeric foams have received increasing attention in both academic and industrial communities. Using of nanoparticles as heterogeneous nucleation agent has been verified as one of the most valid means to enhance cell nucleation and improve cell morphology. However, few researches have been conducted to investigate the effect of the nanoparticles’ spatial orientation on their nucleation efficiency. In this work, to study the influence of the orientation of nanoparticles on their performance in improving morphology of polymeric foam, thermoplastic polyurethane (TPU) composite fibers with different nanoparticles (carbon nanotubes, graphene and SiO₂) were prepared by using different traction speeds. The different traction speeds lead to different orientation state of the nanoparticles which then resulted different nucleation effect. It was found that carbon nanotubes (CNTs) were easily oriented and aligned along the fiber length direction under the high traction speed, while graphene and SiO₂ nanoparticles did not show orientation under the traction speed in this study. As a result, the foam of TPU/CNTs composite fibers from high traction speed exhibited a much smaller cell size and higher cell density compared to the foams of the fibers from low traction speeds, while TPU/graphene, and TPU/SiO₂ composite fibers with different traction speeds showed almost similar cell size and size density after foaming, indicating that the orientated nanoparticles possessed higher heterogeneous nucleation efficiency. To our best knowledge, this work, for the first time, demonstrated the high nucleation effect of the aligned nanoparticles, which hopefully open a new path for improving the cell morphology of polymeric foam materials.     

生物可降解PCL/PLA开孔发泡材料制备及吸油性能

以聚己内酯（PCL）为基体，添加不同含量聚乳酸（PLA）熔融共混制备具有不同分散相形态的PCL/PLA共混物，利用超临界二氧化碳（scCO₂）微孔发泡工艺制备不同发泡倍率和开孔率的PCL/PLA多孔材料用于吸油应用。针对边长3 mm正方体样品溶解度实验发现100 min后CO₂在PCL中已达到饱和吸附状态。PLA分散相含量的增加显著增大了PCL/PLA共混物泡孔密度，并使共混泡孔尺寸减小且分布更加均匀；发泡温度升高6℃，泡孔尺寸增大50%，发泡倍率增大38%，开孔率减小了20%。PCL/PLA开孔材料具有明显的亲油疏水性，发泡倍率越高，疏水性越好；针对花生油和硅油的吸油实验发现材料吸油率与发泡倍率和开孔率整体呈正比，实际吸油量高于理论计算值，10次循环吸油测试后样品吸油率仅降低8.5%，材料吸油量与油品特性黏度关系不大。     

稠油油藏出砂冷采技术实践

套保油田为普通稠油油藏，其开发的难点是常规冷采产能低、递减快，蒸汽吞吐开采注入压力过高破坏隔层导致底水上窜、注入压力过低不能保证注入蒸汽质量导致开采效果差。因此开展出砂冷采试验，经研究及现场试验形成了较完善的配套工艺技术，出砂冷采在套保油田白92块工业化应用，单井日产油达到10～30m^3／d，为常规冷采产量的10～20倍。     

氮气泡沫调驱用泡沫剂性能评价

对辽河油区海外河油田海1块实施氮气泡沫调驱用泡沫剂性能进行评价，其中静态评价内容有泡沫剂与地层水的配伍性，起泡能力和稳定性，油敏性，耐盐抗二价离子能力以及热吸附性；动态评价方内容有动态封堵能力，泡沫剂用量的筛选。评价结果表明，泡沫剂A发泡能力较好，性能稳定，耐钙离子能力强，阻力因子大于4，可与氮气作为暂堵剂体系。建议现场施工中使用泡沫剂A含量为0．5％的泡沫剂溶液，注入量0．2PV，氮气注入量也是0．2PV较适宜。     

以齐聚副产物制备耐高温泡沫剂

以齐聚副产物为原料在实验室分别以AlCl3、AlCl3络合物和杂多酸为催化剂合成并经磺化制备了用于提高石油采收率的耐高温泡沫剂，试验结果说明烷基碳数为16的异构烷基苯磺酸盐常温发泡性能最佳，烷基碳数大于20的正构烷基苯磺酸盐高温发泡性能最佳，后者特别适合高温蒸汽驱油。加入适当的非离子助剂及无机盐能够提高磺酸盐的水溶性，改善发泡剂溶液的稳定性。     

LF泡沫精炼渣脱硫动力学的实验研究

对CaO -Al2 O3 -SiO2 系泡沫精炼渣进行了实验室脱硫动力学研究 ,得到的硫传质系数为 1.45 9× 10 -5m s。还就泡沫精炼渣中发泡剂对其脱硫能力的影响进行了研究。     

乳化炸药的高温化学发泡

文中在阐述ＮＨ４ＮＯ３－ＮａＮＯ２－Ｈ２Ｏ发泡体系的发泡机制的基础上，推导出了就获得较低的反应速率ｒＲ和气体生成量ｎ的高ｐＨ值对高温的平衡关系，从而提出了高温发泡技术。     

夏季面漆起泡的预防

面漆漆膜在夏季潮湿天气下成膜后3—5天，漆膜表面易形成米粒状的漆泡，针对漆泡的现象，寻找其形成的机理，根据起泡的机理采取预防面漆起泡的措施。     

熔体吹气发泡法制备泡沫铝合金研究

泡沫金属是近年来发展起来的一种新型材料。文章采用熔体吹气发泡法制备出了孔径为5．0—8．3mm，壁厚为0．040—0．076mm，密度为0．19—0．40g／cm^3，孔隙率为85．2％—93．0％的Al—Si泡沫铝合金，并着重讨论了发泡温度、气体流量、SiC粉末体积百分含量对泡沫铝合金形成的孔径和壁厚的影响关系。